Installing an electric tankless water heater can be a great way to improve the energy efficiency of your home, as well as provide a steadier supply of hot water. If you're considering upgrading to an Ecosmart 11800 w tankless electric water heater, you're in the right place. This guide will walk you through the installation process, equipping you with the knowledge needed to ensure a safe and successful installation.
Before we dive into the installation steps, it's crucial to understand that while this guide provides a general overview, the specific needs of your home and the complexity of your project may vary. Always consult with a licensed professional if you're unsure about any aspect of the installation process.
Before You Begin: Preparation and Tools
The first step is to ensure you have all the necessary tools and components for the installation. The Ecosmart 11800 w comes with a detailed installation manual, which outlines the specific tools required for the job. In general, you'll need:
- Adjustable wrench
- Screwdriver (both flathead and Phillips)
- Plumbing tape
- Teflon tape
- Electrical tape
- Cable tie or wiring clip
- Voltage tester
- tubing cutter
Additionally, you'll need to ensure your home's electrical system and plumbing are up to the task. The Ecosmart 11800 w requires a dedicated 240V, 90A circuit for electrical power.
Plumbing Preparation
Before installing the water heater, you'll need to shut off the water supply to your home and drain the system. This is crucial to prevent any water damage during the installation process.
First, locate your main water shutoff valve and turn it clockwise to stop the water supply. Then, open all the faucets in your home to relieve any pressure in the system. Lastly, connect a hose to the closest drain valve and open it to drain any remaining water in the pipes.
Electrical Preparation
Next, you'll need to prepare your home's electrical system. As mentioned earlier, the Ecosmart 11800 w requires a dedicated 240V, 90A circuit. If you're unsure about your home's electrical capacity, it's always best to consult with a licensed electrician.
Once you're sure your electrical system can handle the load, you'll need to run a conduits for the power supply and ground wires from the electrical panel to the water heater location. Ensure that the conduits are the correct size and type for the amperage required.
Installing the Ecosmart 11800 w
With the necessary preparations out of the way, you're now ready to install the Ecosmart 11800 w tankless electric water heater. The installation process can be broken down into several key steps:
Mounting the Water Heater
Before you begin, make sure the location you've chosen for the water heater is level, and there's adequate clearance around it for maintenance and operation. Once you've ensured the location is adequate, use the mounting template provided to mark the installation points and secure the water heater to the wall.
Use the appropriate screws and ensure the water heater is securely fastened to the wall. The manual provided with your Ecosmart 11800 w will specify the correct screw type and size.
Plumbing the Water Heater
With the water heater securely mounted, it's time to connect the plumbing. Using the tubing cutter, cut the copper water supply lines to the correct length and insert them into the water heater's inlet and outlet ports. Use plumbing tape to secure the fittings and prevent leaks.
Once the supply lines are connected, you'll need to connect the ground wire from the water heater to the nearest copper water pipe. This is a crucial safety measure to prevent electrical shock in case of a short circuit.
Electrical Connections
Now that the plumbing is connected, it's time to make the electrical connections. First, turn off the power at the main electrical panel to ensure safety during the installation process.
Then, using the appropriate size wire (as specified in your water heater's manual), strip back the insulation and connect the wires to the corresponding terminals on the water heater. Ensure that the wires are secure and properly tightened.
Once the wires are connected, use electrical tape to neatly secure the connections and prevent any exposed wires. Then, replace the access panel and restore power to the circuit.
Testing the Installation
With the installation complete, it's time to test your new Ecosmart 11800 w tankless electric water heater. First, open a hot water faucet in your home and allow the water to run for a few minutes to purge any air from the system.
Plumbing Test
Next, check the plumbing connections for any leaks. If there are no leaks, you've successfully completed the plumbing portion of the installation.
However, if you notice any leaks, tighten the connections and test again. If the leaks persist, you may need to consult a professional plumber to ensure the connections are secure.
Electrical Test
After confirming the plumbing is leak-free, you'll need to test the electrical connections. Using a voltage tester, check the outlets and switches downstream from the water heater to ensure they're hot. This will confirm that the water heater is receiving power.
If the outlets and switches are hot, you've successfully completed the electrical portion of the installation. If not, you may need to troubleshoot the electrical connections or consult with a licensed electrician.
Congratulations! You've now successfully installed your Ecosmart 11800 w tankless electric water heater. Regular maintenance will ensure its continued efficient operation and extend its lifespan. Enjoy the energy savings and consistent hot water that your new water heater provides.