Installing a sink mixer tap might seem like a daunting task, but with the right steps and tools, it's a manageable home improvement project you can DIY. Not only will you save money on installation costs, but you'll also boost your plumbing skills and enjoy a beautiful new fixture. Let's dive into the process, from choosing the right tap to ensuring a secure, leak-free connection to your sink.
Before we start, let's clarify that this guide assumes you're replacing an existing tap with a new one and that your pipes are in good condition. If you're plumbing from scratch or have issues with your existing pipes, consider hiring a professional. Now, let's equip you with the knowledge to tackle this task like a pro.
Tools and Materials Needed
Having the correct tools at hand is crucial for a successful tap installation. Here's a list of what you'll need:
- Adjustable wrench
- Plumber's tape (Teflon tape)
- Socket wrench (may be needed)
- Channel-type pliers
- Plumber's putty
- Work gloves
- New sink mixer tap
- New sink drain and assembly (if replacing)
Choosing the Right Tap
Before purchasing, ensure the new tap will fit your existing sink drain and that it's compatible with your plumbing setup. Consider factors like water pressure, the number of water outlets (single or dual), and style to find the perfect fit.
Popular tap styles include single lever, double lever, and touchless. Single lever controls both hot and cold water, while double lever controls each temperature independently. Touchless taps use sensors for hands-free operation. Choose the one that best serves your needs.
Preparation: Turning Off and Draining Water Supply
Safety first! Before starting, turn off the hot and cold water supply valves located under the sink. If they're too stiff to turn by hand, use an adjustable wrench. After turning off the supplies, open the tap to release any remaining water pressure.
If your tap has a commercial-style aerator that's difficult to unscrew, wrap plumber's tape around the base of the tap first to create a better grip, then try again. Once the tap is off, you'll see two supply lines connected to your sink – a hot and a cold. Make note of their positions, as you'll be connecting the new tap in the same way.
Removing the Old Tap
Using an adjustable wrench, slowly and carefully loosen the nuts connecting the supply lines to the tap's stubby risers (the two short pipes sticking up from the sink). If the nuts are too tight, use a socket wrench for extra torque. Once the nuts are loose, remove the supply lines and risers completely. Now, your old tap should lift off easily.
Inspect your sink for any damage and clean out any debris. If your sink is damaged or you're replacing it, ensure the new one comes with pre-tapped holes for easy tap installation. Always check thetap's compatibility with your sink drain and ensure it's properly supported.
Installing the New Sink Drain (if necessary)
If you're replacing the old sink drain, apply plumber's putty around the threaded base of the new drain. Center it in the hole and push it firmly into place. Next, insert and tighten the rubber gasket and locknut by hand. Use channel-type pliers to snug it up, but be careful not to overtighten and strip the threads.
Flush the drain with water to check for leaks. If it's watertight, install a new drain basket or screen as per the manufacturer's instructions. Now, you're ready to install the new tap.
Installing the New Sink Mixer Tap
Begin by applying plumber's putty around the base of the new tap, just like you did with the drain. Position the tap in the sink and lower it into place. The putty will create a watertight seal as you press down on the tap.
With the tap seated, remove any excess putty from the sides. Now, it's time to connect the supply lines. As mentioned earlier, match the hot and cold water lines to the same sides as the old tap. Wrap Teflon tape around the tap's risers, then screw on the supply lines and tighten them by hand. Use an adjustable wrench to secure them, but avoid overtightening as this can damage the threads.
Reconnecting the Water Supply
Turn the hot and cold water supply valves back on slowly to prevent damage. Check for any leaks around the taps and under the sink. If everything is tight and leak-free, you've successfully installed your new sink mixer tap!
To ensure your tap's longevity, clean debris from the aerator regularly and avoid dropping heavy objects onto the lever. Should any issues arise, consult the manufacturer's instructions or contact a professional plumber.
Congratulations on your newly installed sink mixer tap! By following these steps, you've not only saved money but also gained valuable DIY experience. When the time comes to update other fixtures, you'll have the confidence and know-how to tackle the project. Happy plumbing!